Robonica Port Devices Driver Download

  



Very useful USB driver for Windows 98 based computer. Ratnendra Ashok Posts 601 Registration date Wednesday November 28, 2018 Status Member Last seen. USB™ multi-port adapters with Ethernet connectivity and some Ethernet adapters are not compatible at this time (due to IC design). Click here for more information. The display driver does not support Mac® computers with the M1 processor at this time, contact your computer manufacturer to verify if your computer supports the display driver. Welcome to the NETGEAR Download Center!! To find documentation, firmware, software, or other files, enter a whole or partial Model number in the text search box.

-->

For most devices, the Ports device setup class and the Serial function driver provide the functionality required to operate serial ports and COM ports. To install serial ports and COM ports using these system-supplied components, do the following:

  • Provide an INF file that specifies the Ports device setup class and the Serial function driver as the service for the port.

  • To configure a serial port as COM port, comply with the requirements that are defined in Configuration of COM Ports.

For more information about installing serial ports and COM ports using the Ports device setup class and the Serial function driver, see the following topics:

Robonica Port Devices Driver Download

If you do a custom installation of a COM port, you must comply with the COM port requirements that are defined in Configuration of COM Ports.

The CH340 chip is used by a number of Arduino compatible boards to provide USB connectivity, you may need to install a driver, don’t panic, it’s easier than falling off a log, and much less painful.


Windows

(Manufacturer’s Chinese Info Link)

  1. Download the Windows CH340 Driver
  2. Unzip the file
  3. Run the installer which you unzipped
  4. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Older Windows Driver Version and Instructions

  1. Download the Windows CH340 Driver
  2. Unzip the folder.
  3. If you are running a 64Bit Windows: – run the SETUP_64.EXE installer.
  4. If you are running a 32Bit Windows: – run the SETUP_32.EXE installer.
  5. If you don’t know, try the 64 bit and if it doesn’t work, the 32 bit.
  6. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Macintosh

Robonica Port Devices Driver Download Pc

(Manufacturer’s Chinese Info Link)

The following github has up to day pkg files for 1.3, 1.4 and 1.5 at time of writing, thanks to Joshua Wallis for bringing this to my attention…

Direct Download Links (from the github repo above):

See the github link above for installation instructions if you need them.

Robonica port devices driver download windows 10

Previous macinstosh downloads if the above doesn’t work for you…

(V1.3) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11) and Sierra (10.12)

Inside the zip file you will find a PDF and a “pkg” file, short version, double click the pkg file, the PDF has some extra information.

OSX Sierra (10.12) Note

A kindly user, Maarten Segers reports

Robonica Port Devices Driver Download

FYI, the driver documented here WILL crash on OSX Sierra.

Download
Make sure to use this one instead: https://github.com/MPParsley/ch340g-ch34g-ch34x-mac-os-x-driver
Robonica Port Devices Driver Download

I can personally not test on MacOS and can not vouch for the above drivers at github, but there you go.

See uninstalling information at the bottom of the page if the driver causes problems for you.

Here is an older version of the Mac driver, NOT FOR 10.12 Sierra

Robonica Port Devices Driver Download Windows 10

(V1.0) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11)

Linux

(Manufacturer’s Chinese Info Link)

Drivers are almost certainly built into your Linux kernel already and it will probably just work as soon as you plug it in. If not you can download the Linux CH340 Driver (but I’d recommend just upgrading your Linux install so that you get the “built in” one).

Uninstalling From Macinstosh

A couple of Mac users have said “the driver crashes my mac Sierra how do I uninstall”.

Firstly regards the crash make sure you installed the 1.3 version of the driver, not the old one. You could download it directly from the Manufacturers Website in case they have issued an update since I wrote this page.

Secondly a quick google search reveals that this is how you uninstall:

  1. Open a terminal and type: cd /Library/Extensions/
  2. Verify that the .kext file is present: ls | grep usbserial.kext
  3. Output should be: usbserial.kext
  4. Then type: sudo rm -R usbserial.kext
  5. Verify that the .kext file has been removed: ls | grep usbserial.kext
  6. Output should be empty.
  7. After you should remove the files stored in receipts folder: cd /private/var/db/receipts/
  8. Find the enties: ls | grep usbserial*
  9. Output should be: codebender.cc.ch34xinstaller.usbserial.pkg.bom codebender.cc.ch34xinstaller.usbserial.pkg.plist
  10. Remove each one of the files of the above list: sudo rm -r filename`