If you have bought this device and wants to connect it to PC which is obvious, then this post simply enables you to download the latest Razer Phone USB Drivers for Windows 7, 8 and 10 very simply. If we speak about the specifications, Razer Phone features a 5.7-inches IGZO IPS LCD display with a screen resolution of 1440 x 2560 pixels with. Solution 2: Reinstalling Drivers. If reinstalling the software doesn’t go well in your case, we can try reinstalling all the drivers to the latest version. First, we will not only uninstall Razer drivers but all HID-compliant input devices. This was the key for most of the users in solving their problems.

Frequently Asked Questions

Why do I have an ASUS Aura DRAM device when I don't have an ASUS motherboard?

Many RGB RAM vendors use an RGB control chip that is nearly identical to the one found on early ASUS Aura motherboards. Vendors using this controller include G.Skill, Geil, T-Force, A-DATA, and possibly others. OpenRGB shows all of these devices as 'ASUS Aura DRAM' as they use the same driver as the ASUS Aura motherboards with this chip.

Not all of my ASUS Aura-compatible DRAM modules are showing.

ASUS Aura DRAM modules sometimes get into a state where they won't be detected. It's possible they were assigned an address that OpenRGB doesn't check. If they are not showing after a reboot, you can remove the sticks and install them all in different slots. This appears to reset the on-board RGB controllers and then OpenRGB will detect them on the next power cycle.

I have an ASUS and/or Gigabyte GPU that's not being detected.

OpenRGB has support for ASUS Aura GPUs and Gigabyte RGB Fusion GPUs. However, because these vendors are always improving their products and putting more and more RGB, it's possible your GPU uses a different ASUS Aura or RGB Fusion control chip than the one that OpenRGB supports. The two GPU implementations in OpenRGB only support single lighting zone GPUs. If your GPU has more than one lighting zone, it is likely not supported. I would be glad to help add support for more GPUs, but unfortunately reverse engineering GPUs is fairly complicated and requires a good deal of technical expertise. GPUs are the most difficult RGB devices to reverse engineer that we know of.

OpenRGB won't detect my RAM or Motherboard

OpenRGB uses an interface called SMBus (also referred to as I2C) to communicate with RGB controllers on RAM modules and some motherboards. On Windows, SMBus access requires administrator privileges using a library called inpout32 (inpoutx64 for the 64-bit version). You must run OpenRGB as administrator at least once for inpout32 to set up. Once it has been set up, you may run OpenRGB without administrator and it will be able to access these devices.

If you have problems accessing these devices even after running as administrator, it is possible that a kernel anti-cheat or anti-virus application is blocking the inpout32 driver from functioning. Riot Games' Vanguard (VALORANT) anti-cheat system has been known to block inpout32 as well as some official RGB applications. If you have VALORANT installed, you will have to uninstall it or disable the Vanguard anti-cheat in order to use OpenRGB with these devices.

If you do not have such an anti-cheat system installed and are still having problems, make sure any other RGB applications (ASUS Aura, Corsair iCUE, Gigabyte RGB Fusion, etc) are disabled or uninstalled. This includes disabling their background services. The SMBus only works properly if one application at a time is accessing it, and if two applications try to control the device at the same time, it can confuse the device or put it in an invalid state. This behavior can result in OpenRGB not detecting devices properly.

I'm missing VCRUNTIME140_1.dll

Download the latest Visual C++ runtime from Microsoft here: https://support.microsoft.com/en-us/help/2977003/the-latest-supported-visual-c-downloads

Can I have OpenRGB start automatically when I log in?

Yes! You can create a startup shortcut to OpenRGB and even customize how it starts. Start by creating a shortcut to OpenRGB.exe:

Now you can go into the Properties of your new shortcut to add startup options:

In the Target: field, you can add startup options:

The complete list of startup options is available in the command line interface, but ones that make sense for use in a shortcut are listed below.

Now, to make this shortcut run when you log in to Windows, copy the shortcut file to %APPDATA%MicrosoftWindowsStart MenuProgramsStartup

You can rename the shortcut if you want.

Now simply reboot your computer or log out and log back in. OpenRGB should automatically start with the options you have configured.

Drivers Razer Usb Devices Windows 10

I installed the WinUSB driver for a device and I wish to uninstall it

The WinUSB driver can be removed in Device Manager. Open Device Manager. You should have a category called 'Universal Serial Bus devices'.

Right click on the device you want to uninstall. Click 'Uninstall device'

Check the box that says 'Delete the driver software for this device' and then click Uninstall.

Finally, to have Windows re-detect the device with its original driver, click the 'Scan for hardware changes' button.

My Razer devices aren't being detected

OpenRGB uses the OpenRazer kernel drivers in Linux. Most distributions provide OpenRazer packages. You do not need the OpenRazer daemon but you do need the kernel drivers installed.

My non-Razer USB devices aren't being detected

Drivers Razer Usb Devices Gamepad

You need to install the OpenRGB udev rules. These are provided in the 99-openrgb.rules file in this repository. Copy this file to /etc/udev/rules.d and then trigger a rules reload with the following commands:

sudo udevadm control --reload-rules

sudo udevadm trigger

I have an AMD GPU. Can I use OpenRGB?

GPU support in OpenRGB is already limited to a handful of ASUS and Gigabyte cards, but Linux poses an additional problem for AMD GPU users. AMD's drivers do not expose the GPU's on-board i2c bus, only those for the display connectors. GitHub user twifty has been working on a driver for the AMD GPU i2c bus. It appears to work on Polaris cards but not Vega or Navi cards at the moment. It requires patching your kernel. I have not tested it personally, but I know other users have had it working with OpenRGB for certain ASUS Aura enabled GPUs.

Can I set up OpenRGB as a systemd service?

Yes, use this configuration file, provided in :

Dec 21, 2020 • Filed to: USB Recovery • Proven solutions

After you plug your USB drive to your computer, if you see a balloon popping at the right-hand corner of your screen it means that a malfunction has ensued. You may see something like this:

The USB device is not recognized as the device connected to the PC malfunctioned so your Windows cannot recognize it.

If you see this prompt don’t be alarmed as many before you have faced the same problem. There is a solution to this problem and we will reveal it to you in this article.

Overview of the error

There are several possibilities why this error may have occurred. It may be one of these.

• Malfunctioned ports
• Controller bugs
• Outdated controllers
• Faulty or missing ports

Although several conditions may have necessitated the error there are general solutions that you can try first before the need arises to call in technicians. The solutions here are free and work for the most part so take your time to follow each through. At least one is bound to work for you.

How to Fix it

Method 1- You should try another USB Port

Best Usb Devices

First, try a different USB port so see if the issue will be resolved. If you use a computer, try connecting the USB to the port located behind the computer case as the backport has a stronger electric current than the others

If you use a laptop instead, unplug the USB drive from its port and try another one to see if it will work. Also, avoid using USB Hubs because hubs may sometimes lack sufficient current to power the drive. It is better to plug directly into the system.

If the issue is resolved after changing port it means the port you used before is faulty.

Method 2- Try updating all device drivers

If the first method does not work, you may need to update all your device drivers in case any of them is outdated, faulty, or missing. Make sure you verify that your drivers are working well and to do this you will have to update them either manually or automatically.

Manual update

To update drivers use our Device Manager but if this fails, log on to the manufacturer website of your device for user Support. Search for compatible drivers on their site although this may take some time you will certainly find the correct driver for your system. When you find it, download it on your system by clicking the download link provided. Once the drivers have been downloaded, Microsoft will install them on your device.

Automatic Updates

If you lack the skills or the patience to do the update manually you can complete the process automatically using a 3rd party application like Driver Easy or ant other Automatic driver update program. After downloading the program, launch it and scan for missing, outdated, or faulty drivers. From the list of drivers provided, click each one enables the program to update or replace them one after the other. The update program will scan the web for compatible drivers and install them automatically.

Method 3: Consider disabling USB selective suspend settings

With a selective Suspend feature, you can allocate USB ports of your choice to saving mode like when your PC is on sleep mode. For users of Desktop computers, this feature is unnecessary since it always plugged to a power source. Suspended Setting could be a culprit but it can be disabled all the same.

• Tap your Windows key + S at once and in search bar search for the power plan

• Click the change settings to the exact plan you are using currently

• Click the Change advanced setting

• Click the expand ISB setting and the USB Selective setting

• Disable them from the option below then click on Apply and then OK to save your changes

Kinds Of Usb Devices

*Do note that on laptops you have to click the battery icon then disable it from the menu.

Check if USB is recognizable now. If this doesn’t work proceed to the next method.

Method 4- Try Re-enabling USB Controller driver

A corrupted driver can also cause this kind of problem so try re-enabling drivers again.

• Tap the Windows key + R at once then type this *devmgmt.msc” then tap Enter

• Click view on the too bar then Show all hidden devices

• Expand Universal Serial Controllers

For all drivers marked with a yellow exclamation mark do this

• Right-click the market drivers and uninstall them

• Click Uninstall to proceed

• When they have all been uninstalled, restart your PC then restart the same process with other marked drivers

If you don’t see any driver marked yellow continue

• Right-click the option you see first to disable device

• Once disabled restart your computer and conduct the same process as above. If your driver is not automatically enabled enable it by right-clicking the Enable device

Once you are done your USB will be recognized.

Video Tutorial on How to Fix USB Device Not Recognized

USB Solution

Recover USB Drive

Format USB Drive

Fix/Repair USB Drive

Know USB Drive